A Static Headspace Gas Chromatography Method for Quantitation of Residual Solvents in Nanoformulations.

Various organic solvents are widely used in the manufacturing, processing, and purification of drug substances, drug products, formulations, excipients, etc. These solvents must be removed to the lowest amount permitted, as they do not possess any therapeutic advantages and may cause undesirable toxicities. Therefore, a rapid and sensitive analytical method for the quantitation of residual solvents is needed. The following chapter presents a static headspace gas chromatographic (HSGC) method for determining the concentration of common residual solvents in various nanoformulations. An efficient and sensitive HSGC method has been developed using PerkinElmer's headspace autosampler/gas chromatographic system with a flame ionization detector (FID) and validated according to the International Conference for Harmonization (ICH) guideline Q3C. The method validation indicates that the method is specific, linear, accurate, precise, and sensitive for the analyzed solvents. The method is suitable for the analysis of 13 residual solvents (methanol, ethanol, acetone, diethyl ether, 2-propanol, acetonitrile, 1-propanol, ethyl acetate, tetrahydrofuran, dichloromethane, chloroform, 1-butanol, and pyridine) and utilizes an Elite 624 Crossbond 6% cyanopropylphenyl, 94% dimethylpolysiloxanes column with helium as a carrier gas.

Composition and nutritional values of fatty acids in marine organisms by one-step microwave-assisted extraction/derivatization and comprehensive two-dimensional gas chromatography -flame ionization detector.

This work reports the characterization of the lipidic fraction of seven species of marine organisms gathered along the shoreline of the Po Delta Park of Emilia-Romagna Region (Italy) and of the north Adriatic Sea. Two species of oysters (Crassostrea gigas and Ostrea edulis), two species of clams (Chamelea gallina and Ruditapes philippinarum), one species of mussel (Mytilus galloprovincialis), one species of macroalgae (Ulva rigida), and one species of spiny dogfish (Squalus acanthias) were analyzed to characterize their fatty acids profile and related nutritional value. The lipid fraction was simultaneously extracted and transesterified into fatty acid methyl esters (FAMEs) by using a recently developed one-step microwave-assisted extraction/derivatization (MAED) method. The obtained FAMEs extract was analyzed by a rapid comprehensive multidimensional gas chromatography (GC × GC) method (30 min). The system was equipped with a reverse set of columns (polar × non-polar) connected through a reversed fill/flush flow modulator. The GC × GC system was coupled with a flame-ionization detector (FID) for both qualitative and quantitative purposes. The MAED- GC × GC-FID methodology was suitable in the context of samples containing high percentages of omega-3 PUFA. A total of 82 FAMEs were tentatively identified using standards, literature data, and the two-dimensional plot location. FAME profiles obtained with the proposed approach were comparable with reference methods (AOCS Ce 2b-11), showing no significant differences. Moreover, to determine the food nutritional value of the samples investigated, the most common nutritional indices (index of atherogenicity, index thrombogenicity, hypocholesterolemic/hypercholesterolemic ratio, health-promoting index, unsaturation index, and the fish lipid quality index) were calculated from FAME profiles. Among the samples investigated, Squalus acanthias presented the best nutritional score, while Ruditapes philippinarum had the worst score in 3 out of 6 indices.

Post-mortem formation of ethanol: Is 1-propanol a reliable marker? A proof-of-concept study using an in vitro putrefactive environment setup.

Ethanol is the psychoactive substance identified most frequently in post-mortem specimens. Unfortunately, interpreting post-mortem ethanol concentrations can be difficult because of post-mortem alcohol redistribution and the possibility of post-mortem alcohol neogenesis. Indeed, in the time interval between death and sample collection, the decedent may be exposed to non-controlled environments for an extended period, promoting microbial colonization. Many authors report that in the presence of carbohydrates and other biomolecules, various species of bacteria, yeast, and fungi can synthesize ethanol and other volatile substances in vitro and in vivo. The aim of this study was to study the impact of several variables on microbial ethanol production as well as develop a mathematical model that could estimate the microbial-produced ethanol in correlation with the most significant consensual produced higher alcohol, 1-propanol. An experimental setup was developed using human blood samples and cadaveric fragments incubated under strictly anaerobic conditions to produce a novel substrate, "cadaveric putrefactive blood" mimicking post-mortem corpse conditions. The samples were analyzed daily for ethanol and 1-propanol using an HS-GC-FID validated method. The formation of ethanol was evaluated considering different parameters such as putrefactive stage, blood glucose concentration, storage temperature, and storage time. Statistical analysis was performed using the Mann-Whitney non-parametric test and simple linear regression. The results indicate that the early putrefactive stage, high blood glucose concentration, high temperature, and time of incubation increase microbial ethanol production. In addition, the developed mathematical equation confirms the feasibility of using 1-propanol as a marker of post-mortem ethanol production.

A two-run heart-cut multidimensional gas chromatography method using flame ionization and mass spectrometry for automated and robust determination of nearly complete wine aroma-volatile profiles.

A quantitative analytical method capable of determining the concentrations of 81 aroma-relevant wine volatiles covering nine orders of magnitude was developed and validated in this study. The method is based on stir bar sorptive extraction (SBSE) of 200 µL of wine diluted with 1.8 mL NaCl brine with pH 3.5. Volatiles thermally desorbed from the stir bars were separated in two runs in a heart-cut multidimensional gas chromatographic system and quantified using either a flame ionization detector (FID) in the first dimension (27 aroma compounds) or a mass spectrometer in the second dimension (54 aroma compounds, transferred to 22 cuts). Typical limits of compound detection lay around 0.02 mg/L by FID or ranged from 0.001 to 0.30 µg/L by mass spectrometry detector, liying below the corresponding odor thresholds in all cases. Linearity, reproducibility, and recovery were considered satisfactory for most compounds, with typical R2 values of 0.989-0.999, relative standard deviation below 10 % for 37 compounds and between 10 and 20 % for 44 compounds, and recovery rates of approximately 100 % (85-109 %) for all but acetaldehyde. An analysis of 20 wine samples completed our validation of the method, showing that a single-sample preparation procedure combined with heart-cut multidimensional two-detector gas chromatography can determine wine volatile concentrations ranging from 350 mg/L of isoamyl alcohol to 3.8 ng/L of 3-isobutyl-2-methoxypyrazine.

Method development for forensic oil identification by direct analysis in real time time-of-flight mass spectrometry.

The current well-established chromatography and mass spectrometry based oil spill identification procedures, such as those outlined by the European Committee for Standardization, are highly reliable as methods, highly defensible in the court of law, and widely applicable to the majority of oil spill situations. Nevertheless, the methodology is time consuming and labour intensive, which may not be ideal when dealing with an emergency oil spill situation. In this study, direct analysis in real time time-of-flight mass spectrometry (DART/TOFMS) was used to successfully develop an efficient oil identification method. To confirm the accuracy of this method spilled oil samples were tested from five previous years of blind round robin testing organized by the oil spill identification network of experts (OSINET) under the Bonn Agreement. Heatmap inspection, principal component analysis and finally discriminant analysis of principal components were used to arrive at final predictions regarding the identities of the spilled oil samples. The results were compared with the results of previous gas chromatography flame ionization detection (GC/FID) and gas chromatography triple quadrupole mass spectrometry (GC/MS/MS) analyses of the same oils. While taking only about a tenth of the time, the DART/TOFMS analysis produced results similar to those of classical GC/FID and GC/MS/MS (EI+) procedures. The ability of DART/TOFMS to display this level of validity exemplifies its potential to be a new tool for supplementing classical analyses for oil spill forensics.

Gas chromatography-flame ionization detector for sweat based COVID-19 screening.

Simple approach for rapid screening of corona virus disease 2019 (COVID-19) has been developed. This applied gas chromatography-flame ionization detector (GC-FID) analyzing the potential compound marker in sweat samples obtained from COVID-19 positive and negative volunteers in Bangkok, Thailand. The samples were collected by using cotton rods for 15 min, heated at 90 °C for 5 min, and the volatile compounds in the headspace (HS) were injected (5.00 mL) at 150 °C and separated within 13.7 min. The marker peak was tentatively identified as p-cymene by the authentic standard injection and comparison with the GC-mass spectrometry (GC-MS) and comprehensive two-dimensional GC (GC × GC)-MS analysis. Possible mechanisms for the presence of p-cymene were proposed. The marker peak area thresholds were then varied and optimized via construction of the receiver operating characteristic (ROC) curve. With the optimum threshold, the established method offered the accuracy, sensitivity and specificity of 96 %. This method was insignificantly affected (p-value >0.05) by genders, body mass indices, ages, and use of deodorants as well as the p-cymene containing food. However, the performance could be affected by the population with personal hygiene or experiencing the microbiomes producing p-cymene.

Endogenous n-Alkanes in Vegetable Oils: Validation of a Rapid Offline SPE-GC-FID Method, Comparison with Online LC-GC-FID and Potential for Olive Oil Quality Control.

The potential of endogenous n-alkane profiling for the assessment of extra virgin olive oils (EVOO) adulteration (blends with cheaper vegetable oils) has been studied by relatively few authors. Analytical methods used for this purpose often involve tedious and solvent-intensive sample preparation prior to analytical determination, making them unattractive. A rapid and solvent-sparing offline solid phase extraction (SPE) gas chromatography (GC) flame ionization detection (FID) method for the determination of endogenous n-alkanes in vegetable oils was, therefore, optimized and validated. The optimized method demonstrated good performance characteristics in terms of linearity (R2 > 0.999), recovery (on average 94%), and repeatability (residual standard deviation, RSD < 11.9%). The results were comparable to those obtained with online high-performance liquid chromatography (HPLC)-GC- FID ( RSD < 5.1%). As an example of an application to prove the potentiality of endogenous n-alkanes in revealing frauds, the data set obtained from 16 EVOO, 9 avocado oils (AVO), and 13 sunflower oils (SFO), purchased from the market, was subjected to statistical analysis and principal component analysis. Two powerful indices, namely (n-C29 + n-C31)/(n-C25 + n-C26) and n-C29/n-C25, were found to reveal the addition of 2% SFO in EVOO and 5% AVO in EVOO, respectively. Further studies are needed to confirm the validity of these promising indices.

Separation and quantification of diazinon in water samples using liquid-phase microextraction-based effervescent tablet-assisted switchable solvent method coupled to gas chromatography-flame ionization detection.

This study used a liquid-phase microextraction-based effervescent tablet-assisted switchable solvent method coupled to gas chromatography-flame ionization detection as an eco-efficient, convenient-to-use, cost-effective, sensitive, rapid, and efficient method for extracting, preconcentrating, and quantifying trace amounts of diazinon in river water samples. As a switchable solvent, triethylamine (TEA) was used. In situ generation of CO2 using effervescent tablet containing Na2 CO3 and citric acid changed the hydrophobic TEA to the hydrophilic protonated triethylamine carbonate (P-TEA-C). CO2 removal from the specimen solution using NaOH caused P-TEA-C to be converted into TEA and led to phase separation, during which diazinon was extracted into the TEA phase. The salting-out process was helpful in enhancing extraction efficiency. In addition, a number of significant parameters that affect extraction recovery were examined. Under optimum conditions, the limit of detection and limit of quantitation were 0.06 and 0.2 ng/ml, respectively. The extraction recovery percentage and pre-concentration factor were obtained at 95 and 190%, respectively, and the precision (inter- and intra-day, relative standard deviation %, n = 5) was <5%.

Hybrid volatilomics in cancer diagnosis by HS-GC-FID fingerprinting.

Assessing volatile organic compounds (VOCs) as cancer signatures is one of the most promising techniques toward developing non-invasive, simple, and affordable diagnosis. Here, we have evaluated the feasibility of employing static headspace extraction (HS) followed by gas chromatography with flame ionization detector (GC-FID) as a screening tool to discriminate between cancer patients (head and neck-HNC,n= 15; and gastrointestinal cancer-GIC,n= 19) and healthy controls (n= 37) on the basis of a non-target (fingerprinting) analysis of oral fluid and urine. We evaluated the discrimination considering a single bodily fluid and adopting the hybrid approach, in which the oral fluid and urinary VOCs profiles were combined through data fusion. We used supervised orthogonal partial least squares discriminant analysis for classification, and we assessed the prediction power of the models by analyzing the values of goodness of prediction (Q2Y), area under the curve (AUC), sensitivity, and specificity. The individual models HNC urine, HNC oral fluid, and GIC oral fluid successfully discriminated between healthy controls and positive samples (Q2Y = 0.560, 0.525, and 0.559; AUC = 0.814, 0.850, and 0.926; sensitivity = 84.8, 70.2, and 78.6%; and specificity = 82.3; 81.5; 87.5%, respectively), whereas GIC urine was not adequate (Q2Y = 0.292, AUC = 0.694, sensitivity = 66.1%, and specificity = 77.0%). Compared to the respective individual models, Q2Y for the hybrid models increased (0.623 for hybrid HNC and 0.562 for hybrid GIC). However, sensitivity was higher for HNC urine and GIC oral fluid than for hybrid HNC (75.6%) and hybrid GIC (69.8%), respectively. These results suggested that HS-GC-FID fingerprinting is suitable and holds great potential for cancer screening. Additionally, the hybrid approach tends to increase the predictive power if the individual models present suitable quality parameter values. Otherwise, it is more advantageous to use a single body fluid for analysis.

Determination of variability of terpenes and terpenoids in Cannabis sativa by gas chromatography-flame ionization detection and gas chromatography-mass spectrometry.

Absolute content of terpenes in inflorescences of two strains of Cannabis sativa L., CAT 1 and CAT 3, has been determined. Twenty terpenes commonly present in these samples were quantified by solid phase microextraction combined with gas chromatography and flame ionization detection (SPME/GC-FID). High amounts of ß-myrcene, α-pinene, ß-pinene, limonene, (E)-ß-ocimene, ß-caryophyllene, α-humulene, (E)-nerolidol, and linalool, were found in both strains. Lower concentrations (< 20 µg·g-1) of other terpenes were also determined. Only (E)-ß-ocimene was detected at 50 µg·g-1 in CAT 3 whereas it was below the LOD in CAT 1. Concentrations of other compounds for which standards were not available, were estimated based on a response factor obtained from the calibration curves of compounds with similar chemical structures. Fingerprints of both CAT strains were obtained and the identities of most volatile compounds were assigned using gas chromatography coupled to mass spectrometer detector (GC-MS). Additionally, an assessment of variability of terpenes was achieved by analyzing ten plants of each strain grown under controlled conditions and harvested at the same time. This variability was about 20%, considering terpenes at concentration above 20 µg·g-1.

Comparative Evaluation of Carboxyhemoglobin Quantification in Postmortem Whole Blood by CO-Oximetry and Headspace Gas Chromatography with Flame Ionization Detection and Atom Absorption Spectrophotometry.

A comparative evaluation of two methods used for carboxyhemoglobin (COHb) determination in postmortem whole blood was performed: carbon monoxide (CO)-oximetry measuring at 128 wavelengths and headspace gas chromatography with flame ionization detection (HS-GC--FID) where CO was determined after catalytic reduction of CO to CH4 and Fe was determined by atom absorption spectrophotometry (AAS, 248.3 nm). An aliquot of 100 µL whole blood was loaded into the CO-oximetry module. In the HS-GC--FID analysis, to 1.0 mL of whole blood, 3.0 mL of saponin solution was added, mixed and centrifuged. To 20 mL HS vials, 400 µL of the supernatant was added and the vials were immediately sealed. One milliliter of potassium hexacyanoferrat (III) solution was added through the HS septum and mixed. The samples were incubated at 70°C for 5 min. CO was separated using He as carrier gas and a CP-Molsieve 5 Å PLOT capillary column. Fe was determined using 400 µL of the saponin supernatant diluted to 10 mL by water. During a period of ∼3 years, 124 postmortem whole blood samples were analyzed. Bland-Altman method comparison showed satisfactory agreement and no significant bias between the methods for the whole saturation range (5 to 85% COHb). Five samples, all with %COHb >40, showed deviations of more than 10% COHb in absolute terms. One sample, in the lower COHb range <10%, was false negative on the CO-oximetry method. The between-assay accuracy, reported as bias, at 60% COHb was -0.8% and -9.0%, and precision, reported as relative standard deviation, was 1.6% and 7.7%, for the CO-oximetry and HS-GC--FID-AAS methods, respectively. Both methods obtained satisfactory results in proficiency testing rounds, with z-scores <±2 (n = 11). This study showed that the CO-oximetry method based on the 128-wavelength principle and the HS-GC--FID-AAS method are comparable and satisfactory for %COHb determination in postmortem whole blood.

Assessment of gas chromatography methodology approach for the trace evaluation of carcinogenic impurity, methyl chloride, in trimetazidine dihydrochloride.

OBJECTIVE: A simple and robust head space/gas chromatography with flame ionisation sensor (HS/GC/FIS) approach for the trace evaluation of carcinogenic impurity, methyl chloride, in trimetazidine dihydrochloride (TRD) drug ingredient and its formulation is described. METHOD: This HS/GC/FIS approach was based on separation and analysis of CH3Cl content on DB-624 [75.0m - length, 0.53mm - internal diameter, 3.0µm - film thickness] column using nitrogen as carrier gas flowing through the column at 3mL/min stream rate. Detection of eluted CH3Cl was accomplished with flame ionization sensor at a set temperature of 260̊C. RESULTS: The optimised HS/GC/FIS methodological approach was thoroughly validated, demonstrating that it was linear with range of 5.0ppm to 1508.4ppm, sensitive with detection limit of 1.65ppm and quantification limit of 5.01ppm, reproducible with RSD values of 2.10-2.35%, accurate with recoveries of 81.9-99.0%, robust with percent variation of 7.5-12.22% with respect to changes in oven temperature, injector temperature, detector temperature and practical for regular TRD quality control. CONCLUSION: The findings revealed that with this optimised HS/GC/FIS methodological approach, the trace amounts of carcinogenic impurity (methyl chloride) in TRD drug ingredient and formulation could be successfully measured.

Combination of Multidimensional Instrumental Analysis and the Ames Test for the Toxicological Evaluation of Mineral Oil Aromatic Hydrocarbons.

Mineral oil aromatic hydrocarbons (MOAHs) include mutagenic and carcinogenic substances and are considered a potential health risk. Current methods address the total MOAH content but cannot address the actual toxicological hazard of individual components. This work presents a combined methodology closing those gaps: high-performance liquid chromatography (HPLC) coupled to gas chromatography with flame ionization detection was used to determine the MOAH content. To characterize present substance classes, comprehensive two-dimensional gas chromatography with time-of-flight mass spectrometry was applied. Preparative HPLC separated MOAHs into subgroups, which were tested with a miniaturized Ames test evaluating DNA reactivity of isolated fractions. Combining these methods allowed a correlation between present subgroups and DNA reactivity. The developed approach was applied to a mineral oil and distinguished between not DNA-reactive mono- and diaromatics and DNA-reactive tri- and polyaromatics, providing a proof of concept. Hereinafter, it will be applied to diverse sample matrices including mineral oils, food, and food contact materials.

Improvement of methods for analysing sucrose acetate isobutyrate (SAIB) in soft drinks using GC-FID and evaluating antioxidant effects in the SAIB emulsion system.

Sucrose acetate isobutyrate SAIB (E444) is a mixture produced by the esterification of sucrose with acetic anhydride and isobutyric anhydride. It is a food additive that is used as an emulsifier in soft drinks. It is difficult to analyse SAIB quantitatively because there are 256 synthesisable structures in the mixture. This study developed an analytical method for SAIB using gas chromatography-flame ionization detection (GC-FID). The pre-treatment of SAIB in soft drinks was performed using a liquid-liquid extraction method, which demonstrated a recovery rate of 107.8 ± 7.2%. In the GC-FID analysis of SAIB, numerous peaks were observed in the chromatogram, and the content of SAIB was calculated as the sum of these peak areas. A series of analytical methods were validated according to International Conference for Harmonization (ICH) guidelines. Accordingly, the applicability of the developed analytical method was confirmed for both domestic and imported soft drinks distributed in Korea. Additionally, in the linoleic acid emulsion, SAIB exhibited better lipid oxidation stability than the natural antioxidant α-tocopherol and had similar efficacy to the synthetic antioxidant butylated hydroxytoluene (BHT). Although SAIB has excellent lipid oxidation stability, it must be used within legal standards according to consumer demand to reduce the use of synthetic materials in processed foods. The validated GC-FID analytical method will enable subsequent monitoring of the distributed products.

Development of a Gas-Tight Syringe Headspace GC-FID Method for the Detection of Ethanol, and a Description of the Legal and Practical Framework for Its Analysis, in Samples of English and Welsh Motorists' Blood and Urine.

Ethanol is the most commonly used recreational drug worldwide. This study describes the development and validation of a headspace gas chromatography flame ionisation detection (HS-GC-FID) method using dual columns and detectors for simultaneous separation and quantitation. The use of a dual-column, dual-detector HS-GC-FID to quantitate ethanol is a common analytical technique in forensic toxicology; however, most analytical systems utilise pressure-balance injection rather than a simplified gas-tight syringe, as per this technique. This study is the first to develop and validate a technique that meets the specifications of the United Kingdom's requirements for road traffic toxicology testing using a Shimadzu GC-2014 gas-tight syringe. The calibration ranged from 10 to 400 mg/100 mL, with a target minimum linearity of r2 > 0.999, using tertiary butanol as the internal standard marker. The method has an expanded uncertainty at 99.73% confidence of 3.64% at 80 mg/100 mL, which is the blood alcohol limit for drink driving in England and Wales. In addition, at 200 mg%­the limit at which a custodial sentence may be imposed on the defendant­the expanded uncertainty was 1.95%. For both the 80 mg% and 200 mg% concentrations, no bias was present in the analytical method. This method displays sufficient separation for other alcohols, such as methanol, isopropanol, acetaldehyde, and acetone. The validation of this technique complies with the recommended laboratory guidelines set out by United Kingdom and Ireland Association of Forensic Toxicologists (UKIAFT), the recently issued Laboratory 51 guidelines by the United Kingdom Accreditation Service (UKAS), and the criteria set out by the California Code of Regulations (CCR), 17 CCR § 1220.1.

Low-Cost Detection of Methane Gas in Rice Cultivation by Gas Chromatography-Flame Ionization Detector Based on Manual Injection and Split Pattern.

Rice cultivation is one of the most significant human-created sources of methane gas. How to accurately measure the methane concentration produced by rice cultivation has become a major problem. The price of the automatic gas sampler used as a national standard for methane detection (HJ 38-2017) is higher than that of gas chromatography, which greatly increases the difficulty of methane detection in the laboratory. This study established a novel methane detection method based on manual injection and split pattern by changing the parameters of the national standard method without adding any additional automatic gas samplers. The standard curve and correlation coefficient obtained from the parallel determination of methane standard gas were y = 2.4192x + 0.1294 and 0.9998, respectively. Relative standard deviation (RSD, <2.82%), recycle rate (99.67−102.02%), limit of detection (LOD, 0.0567 ppm) and limit of quantification (LOQ, 0.189 ppm) of this manual injection method are satisfying, demonstrating that a gas chromatography-flame ionization detector (GC-FID), based on manual injection at a split ratio (SR) of 5:1, could be an effective and accurate method for methane detection. Methane gases produced by three kinds of low-methane rice treated with oxantel pamoate acid, fumaric acid and alcohol, were also collected and detected using the proposed manual injection approach Good peak shapes were obtained, indicating that this approach could also be used for quantification of methane concentration.

Quantification and characterization of mineral oil in fish feed by liquid chromatography-gas chromatography-flame ionization detector and liquid chromatography-comprehensive multidimensional gas chromatography-time-of-flight mass spectrometer/flame ionization detector.

Mineral oil is an ubiquitous food contaminant potentially toxic. It is generally divided into aromatic hydrocarbons (MOAH) and saturated hydrocarbons (MOSH). These compounds are currently under investigation by the European Union to determine their occurrence and their toxicity before legislating on the matter. Although the discussion mainly focuses on food, animal feed can indirectly contribute to human exposure to such a contaminant. In this study, seven commercial feeds were analyzed. The analyses were carried out in two different Universities (Udine-IT and Liège-BE), performing the same sample preparation protocol: microwave-assisted saponification and extraction followed by epoxidation for the MOAH fraction. The final determination was performed by hyphenated liquid-gas chromatography (LC-GC) and LC coupled to comprehensive multidimensional gas chromatography (LC-GC × GC) with parallel detection, namely flame ionization detector (FID) and time-of-flight mass spectrometer (ToFMS). The results obtained by the two laboratories were generally in good agreement. The results obtained by LC-GC × GC-ToFMS/FID platform provided consistent results, with the advantages of more robust data interpretation that can compensate for problems occurring during purification. Moreover, the coupling of enhanced separation obtained by GC × GC and the MS information allowed for a more in-depth characterization of the contamination.

A stir bar sorptive extraction device coupled with a gas chromatography flame ionization detector for the determination of abused prescription drugs in lean cocktail samples.

A lean cocktail is a mixed drink for the non-medical use of prescription medications that has emerged in recent years as a drug of abuse and is related to drug-facilitated crimes. The determination of active ingredients in a lean cocktail is necessary for forensic investigations. This work presents an in-house developed stir bar sorptive extraction (SBSE) device with an XAD-2 adsorbent followed by analysis using GC-FID for the extraction and determination of the five main abused prescription drugs (diphenhydramine, tramadol, chlorpheniramine, dextromethorphan and promethazine) in lean cocktail samples. Under optimized conditions, the developed method provided linearity for 1.0-250 µg mL-1 of each of the five abused prescription drugs. The limits of detection and limits of quantitation were in the respective ranges of 0.25-0.5 µg mL-1 and 1.0-1.5 µg mL-1. The percentage of extraction was 85.0-94.9%. The intra-day and inter-day precisions were 1.2-14.4% RSD and 1.4-15.8% RSD, respectively. Good relative recoveries in the range of 86.7-110.3% and 88.5-107.9% were obtained when the proposed method was applied for extraction and analysis of abused prescription drugs in five lean cocktail samples. The developed method can be a useful tool for measuring the levels of abused prescription drugs in a lean cocktail and the data could also be used as evidence in a forensic investigation.

Simultaneous determination of trace level riot control agents in environmental water by solid-phase microextraction and gas chromatography coupled with a flame ionization detector.

In this paper, a direct immersion solid-phase microextraction procedure for the simultaneous analyses of four primary riot control agents: 2-chloroacetophenone, o-chlorobenzylidene malonitrile, dibenz(b,f)-1,4-oxazepine, and oleoresin capsicum at µg/L concentration from environmental water was developed. Several parameters that influence the extraction effectiveness were investigated, including fiber type, extraction temperature, extraction time, starring rate, and salinity. Under the recommended conditions, the optimized method had reasonable linearity and accuracy. The average recovery of this method ranged from 84 to 108.1%. The limit of detection for all the analytes ranged from 0.2 to 3 µg/L and the limit of quantification ranged from 1 to 10 µg/L, respectively. A relative standard deviation from 3.0 to 4.3% can be achieved depending on the compounds. The procedure was applied to analyze all the four riot control agents simultaneously in several environmental samples.

In situ quantitative analysis by ultrasonic extraction and nebulization combined with hydrogen flame ionization mass spectrometry: Diisopropylnaphthalene (DIPN), a marker of recycled paper in packing materials.

Ambient mass spectrometry is used for direct analysis and high-throughput screening in many fields. However, most researches are about qualitative analysis. Quantitative detection based on AMS only performs on standard compounds and the relative standard deviation is so large that the accuracy of the result is low. In this study, a hydrogen flame ion source with ultrasonic nebulizer as sampling unit was established to enable solid samples to extract, nebulize and quantitatively detect in situ, with high sensitivity. This device was used to quantificationally determine the content of diisopropylnaphthalene (DIPN) in food packaging paper to identify recycled paper. Rapid analysis was performed in situ without complex pretreatment and the whole analysis time was less than 10 min. It's environmentally friendly that only 100 mg (or less) of sample and no more than 1 mL of solvent are required for one test. The external standard method was used for quantitative determination. The limit of detection was measured to be as low as 0.01 ng mL-1 and the linear dynamic range was 0.03-0.60 µg mL-1 in positive multiple reactions monitoring mode. It has been successfully applied to detect actual samples and the content of DIPN was 0.020-0.095 mg kg-1.